Faculty Database - Kubota Hisao

Books and Papers

Academic Qualifications

Academic Associations Membership

Research Topics, Consignment Studies & KAKENHI Researches

Current Specialized Field

（Last updated : 2025-03-17 12:13:58）

Kubota Hisao
Department Undergraduate School , School of Science and Technology

Position Professor

■ Books and Papers

1.	2024/11	Article	Suppression of Velocity Pulsations with Resonant Controllers in Sensorless Vector Control of Permanent Magnet Synchronous Motors 27th International Conference on Electrical Machines and Systems (ICEMS2024) pp.524-531 (Collaboration)
2.	2024/04	Article	Suppression of Periodic Velocity Pulsation in Sensorless Vector Control of PMSM IEEJ Transactions on Industry Applications 144(4),pp.175-181 (Collaboration)
3.	2022/05	Article	Compensation of Zero Current Clamping Phenomenon of Sensorless IPMSM Drives with Ultrasonic Signal Injection 2022 International Power Electronics Conference, IPEC-Himeji 2022 -ECCE Asia- pp.368-371 (Collaboration)
4.	2020/07	Article	High Power Density Inverter Utilizing SiC MOSFET and Interstitial Via Hole PCB for Motor Drive System pp.526-533 (Collaboration)
5.	2020/02	Article	Power Loss Determination Methods for Complete Drive Module Corresponding to International Standards for the Energy Efficiency of Power Drive Systems pp.71-78 (Collaboration)
6.	2019/11	Article	Position Sensorless Control Method for Permanent Magnet Synchronous Motors Using Speed Observer and Opened Phase Voltage Caused by Magnetic Saliency IEEJ Journal of Industry Applications 8(6),pp.875-883 (Collaboration)
7.	2019/03	Article	Instantaneous Balancing of Neutral-Point Voltages for Stacked DC-Link Capacitors of a Multilevel Inverter for Dual-Inverter-Fed Induction Motor Drives IEEE Transactions on Power Electronics 34(3),pp.2505-2514 (Collaboration)
8.	2018/10	Article	Acoustic Noise Removal of Sensorless Control for an IPMSM Based on Extended EMF and Voltage Injection Synchronized with PWM Carrier IECON 2018 - 44th Annual Conference of the IEEE Industrial Electronics Society (Collaboration)
9.	2018/10	Article	Quiet Position Sensorless Drive of IPMSM Using Ultrasonic Three-Phase Triangular-Wave Carrier IECON 2018 - 44th Annual Conference of the IEEE Industrial Electronics Society (Collaboration)
10.	2018/06	Book	A Stacked 7-Level Common Mode Voltage Eliminated Inverter Scheme with Single DC-link for Open-End Induction Motor Drive PCIM Europe 2018; International Exhibition and Conference for Power Electronics, Intelligent Motion, (Collaboration)
11.	2018/05	Article	A quiet position sensorless control for an IPMSM based on Extended EMF and Voltage injection Synchronized with PWM Carrier 2018 International Power Electronics Conference (IPEC-Niigata 2018 -ECCE Asia) (Collaboration)
12.	2017/12	Article	Position-sensorless control method for permanent magnet synchronous motor using speed observer and induced voltage caused by magnetic saturation 2017 IEEE 12th International Conference on Power Electronics and Drive Systems (PEDS) (Collaboration)
13.	2016/03	Article	Position Sensorless Control for IPMSM Based on Extended EMF and Voltage Injection Synchronized with PWM Carrier IEEJ Transactions on Industry Applications 136(3),pp.212-221 (Collaboration)
14.	2015/09	Article	Position sensorless drive for IPMSM based on EEMF with maximum torque control in all speed ranges 2015 IEEE Energy Conversion Congress and Exposition (ECCE) (Collaboration)
15.	2015/09	Article	The proposal of low speed sensorless drives by symmetrical carrier PWM 2015 17th European Conference on Power Electronics and Applications (EPE'15 ECCE-Europe) (Collaboration)
16.	2015/05	Article	Audible Noise Reduction Method in IPMSM Position Sensorless Control Based on High-Frequency Current Injection IEEJ Journal of Industry Applications 4(3),pp.180-186 (Collaboration)
17.	2015/03	Article	Acoustic noise characteristics in position sensorless control for IPMSM based on EEMF and voltage injection synchronized with PWM carrier 2015 IEEE International Conference on Industrial Technology (ICIT) (Collaboration)
18.	2014/11	Article	Improved independent vector control of 2PMSM fed by a five-leg inverter reducing common leg peak current 2014 International Power Electronics and Application Conference and Exposition (Collaboration)
19.	2014/10	Article	Independent rated speed control of two induction motors fed by a four-leg inverter 2014 IEEE Industry Application Society Annual Meeting (Collaboration)
20.	2014/10	Article	Vector control of two induction motor drives fed by matrix converter IECON 2014 - 40th Annual Conference of the IEEE Industrial Electronics Society (Collaboration)
21.	2014/10	Article	Vector controlled two induction motor drives fed by matrix converter 2014 IEEE Industry Application Society Annual Meeting (Collaboration)
22.	2014/09	Article	Study of the Magnetization Method Suitable for Fractional-Slot Concentrated-Winding Variable Magnetomotive-Force Memory Motor IEEE Transactions on Power Electronics 29(9),pp.4877-4887 (Collaboration)
23.	2014/05	Article	Audible noise reduction method in IPMSM position sensorless control based on high-frequency current injection 2014 International Power Electronics Conference (IPEC-Hiroshima 2014 - ECCE-ASIA) pp.3119-3123 (Collaboration)
24.	2014/05	Article	EMI prediction method for SiC inverter by the modeling of structure and the accurate model of power device 2014 International Power Electronics Conference (IPEC-Hiroshima 2014 - ECCE-ASIA) pp.1929-1934 (Collaboration)
25.	2014/05	Article	Independent speed and position control of two permanent magnet synchronous motors fed by a four-leg inverter 2014 International Power Electronics Conference (IPEC-Hiroshima 2014 - ECCE-ASIA) pp.3134-3139 (Collaboration)
26.	2014/05	Article	Study of low speed sensorless drives for SPMSM by controlling elliptical inductance 2014 International Power Electronics Conference (IPEC-Hiroshima 2014 - ECCE-ASIA) pp.919-924 (Collaboration)
27.	2014/04	Article	EMI Prediction Method for SiC Inverter by Developing an Accurate Model of Power Device IEEJ Transactions on Industry Applications 134(04),pp.461-467 (Collaboration)
28.	2014/01	Article	Study of Low-Speed Sensorless Control of SPMSM by Controlling the Elliptical Inductance IEEJ Transactions on Industry Applications 134(1),pp.106-114 (Collaboration)
29.	2014/01	Article	Three-Phase Current Reproduction Method using the DC Current Sensor Capable of Suppressing a Harmonic Noise IEEJ Transactions on Industry Applications 134(01),pp.96-105 (Collaboration)
30.	2013/04	Article	Position Estimating Method of IPMSM at Low Speed Region Using dq-axis Current Derivative Without High Frequency Component The 10th IEEE International Conference on Power Electronics and Drive Systems (PEDS'13) (Collaboration)
31.	2013/04	Article	Position Sensorless Control for IPMSM Based on Extended EMF Using Voltage Injection Synchronized with PWM Carrier The 10th IEEE International Conference on Power Electronics and Drive Systems (PEDS'13) (Collaboration)
32.	2013/01	Article	Sensorless Vector Control of Closed-slot　Induction Machines at Low Frequency IEEJ Journal of Industry Applications 2(1),pp.74-78 (Collaboration)
33.	2012/10	Article	Flux position estimating method of IPMSM at low speed region using current derivative without high frequency component injection 15th International Conference on Electrical Machines and Systems (ICEMS) 2012 (Collaboration)
34.	2012/03	Article	Flux Position Estimation Method of IPMSM by Controlling Current Derivative at Zero Voltage Vector Journal of International Conference on Electrical Machines and Systems 1(1),pp.84-90 (Collaboration)
35.	2011	Article	A Simple Design Method Based on Vector Control of AC Machines with LC Filter Electrical Engineering in Japan 176(4),pp.45-51 (Collaboration)
36.	2010/10	Article	Analysis of Common-mode Voltage Elimination of PWM Inverter with Auxiliary Inverter 2010 International Conference on Electrical Machines and Systems (Collaboration)
37.	2010/10	Article	Flux Position Estimation Method of IPMSM By Controlling Current Derivative at Zero Voltage Vector 2010 International Conference on Electrical Machines and Systems (Collaboration)
38.	2010/06	Article	Dead-time Effect and its Compensation in Common-mode Voltage Elimination of PWM Inverter with Auxiliary Inverter The 2010 International Power Electronics Conference pp.222-227 (Collaboration)
39.	2010/06	Article	Stabilization of Position Sensor-less Control for Low-Inductance and High-Speed PMSM with Reduced Order Flux Observer The 2010 International Power Electronics Conference pp.1412-1415 (Collaboration)
40.	2010	Article	Sensorless Vector Control of IPMSM with DC Link Current Measurement at Low Speeds Electrical Engineering in Japan 172,(4),pp.58-63 (Collaboration)
41.	2009/11	Article	Improvement of Current Waveforms of Position Sensor-less Vector Controlled Permanent Magnet Synchronous Motor at High Frequency Region International Conference on Electrical Machines and Systems (ICEMS 2009) (Collaboration)
42.	2009/11	Article	Investigation of Common-Mode Voltages of PWM Inverter with a Small Capacity Auxiliary Inverter International Conference on Electrical Machines and Systems (ICEMS 2009) (Collaboration)
43.	2009/09	Article	A Novel Approach to Eliminating Common-Mode Voltages of PWM Inverter with a Small Capacity Auxiliary Inverter 13th European Conference on Power Electronics and Applications (Collaboration)
44.	2009/02	Article	Pole Position Estimation Method of IPMSM at Low Speed without High Frequency Components Injection THE IEEE APPLIED POWER ELECTRONICS CONFERENCE AND EXPOSITION (APEC 2009) (Collaboration)
45.	2008/10	Article	Design of Voltage Controller of Single-phase Inverter for Harmonic Rejection International Conference on Electrical Machines and Systems (ICEMS 2008) (Collaboration)
46.	2008/10	Article	Experimental Study on Identification of the Parameters on α-βaxis of LIM by DC Decay Testing Method International Conference on Electrical Machines and Systems (ICEMS 2008) (Collaboration)
47.	2008/10	Article	High Frequency Region Position Sensor-less Vector Control of Interior Permanent Magnet Synchronous Motor Drives International Conference on Electrical Machines and Systems (ICEMS 2008) (Collaboration)
48.	2008/10	Article	Speed Estimation of Induction Motor by Using Observer and PWM Carrier Frequency Components International Conference on Electrical Machines and Systems (ICEMS 2008) (Collaboration)
49.	2007/11	Article	Compensation of Pole Position Estimation Error for Sensor-less IPMSM Drives with DC Link Current Detection Proc. of International Conference on Power Electronics and Drive Systems pp.17-21 (Collaboration)
50.	2007/10	Article	Stability Analysis of Sensor-less Induction Motor Drives with Stator Resistance Adaptation using Estimation Error Index Proceeding of International Conference on Electrical Machines and Systems 2007 (Collaboration)
51.	2007/09	Article	A Simple Design Method Based on Vector Control of AC Machines with LC Filter 12th European Conference on Power Electronics and Applications (Collaboration)
52.	2007/04	Article	Flux Position Estimation of Closed Slot Induction Machine with Three Phase Triangular Carrier Waves at Low Speeds The Fourth Power Conversion Conference pp.275-278 (Collaboration)
53.	2007/04	Article	Initial Pole Position Estimation of IPMSM with DC Link Current Measurement - Approach for Weak Saturation Effect Machines - The Fourth Power Conversion Conference pp.302-307 (Collaboration)
54.	2007/02	Article	Investigation of IPMSM’s Position Estimation in Low Speed Region with DC Link Current Detection Twenty-Second Annual IEEE Applied Power Electronics Conference and Exposition pp.1411-1416 (Collaboration)
55.	2006/11	Article	A Simple Vector Control of AC Machines with an LC Filter The 2006 International Conference on Electric Machines and Systems (Collaboration)
56.	2006/11	Article	Investigation of IPMSM's Position Estimation in Very Low Speed Region with DC Link Current Detection Proc. of the 32nd Annual Conference of the IEEE Industrial Electronics Society (Collaboration)
57.	2006/11	Article	Sensor-less Induction Motor Drives with Stator Resistance Adaptation using Estimation Error Index The 2006 International Conference on Electric Machines and Systems (Collaboration)
58.	2005/09	Article	Fast Response Control of DC-DC Converter PROCEEDINGS OF THE EIGHTH INTERNATIONAL CONFERENCE ON ELECTRICAL MACHINES AND SYSTEMS pp.1414-1417 (Collaboration)
59.	2005/09	Article	Thrust Ripple Reduction of Linear Induction Motor with Direct Torque Control PROCEEDINGS OF THE EIGHTH INTERNATIONAL CONFERENCE ON ELECTRICAL MACHINES AND SYSTEMS pp.655-658 (Collaboration)
60.	2005/04	Article	Position Estimation of IPMSM with DC Link Current Measurement and Three Phase Triangular Carrier Wave International Power Electronics Conference (Collaboration)
61.	2004/11	Article	Sensorless IPMSM Drives Based on Pilot-Voltage Supply and Speed Observer International Conference on Electrical Machines and Systems (Collaboration)
62.	2004/06	Article	Adaptive Observer-Based Sensorless Induction Motor Drives Robust Against Stator Resistance Variation Symposium on Power Electronics, Electrical Drives, Automation and Motion (Collaboration)
63.	2002/11	Article	Stator Resistance Estimation for Sensorless Induction Motor Drives under Regenerating Condition Proc. of the 28th Annual Conference of the IEEE Industrial Electronics Society
64.	2002/07	Article	Regenerating-Mode Low-Speed Operation of Sensor-less Induction Motor Drive With Adaptive Observer IEEE Transactions on Industry Applications 38(4),pp.1081-1086
65.	2001/10	Article	Stable Operation of Adaptive Observer Based Sensorless Inducation Motor Drives in Regenerating Mode at Low Speeds Proc. IEEE Industry Applications Society Annual Meeting pp.469-474 (Collaboration)
66.	2001/03	Article	Control Avoiding Zero Frequency for Sensorless Vector Controlled Induction Motor Drive Using Flux Adjustment
67.	2001/03	Article	Effect of Core Loss Resistance on Identification of Rotor Time Constant for Induction Machine Based on Instantaneous Reactive Power
68.	2001/03	Article	Experimental Investigation with Nonlinear Friction Compensation Method in Linear Motors Using Neural Network
69.	2001/03	Article	Sensorless Drives of IPM Motors Using Speed Observer and Pilot Voltage Injection
70.	2001/01	Article	Characteristic Improvement of Sensorless Vector Controlled Induction Motor Drive using Flux Adjustment
71.	2001/01	Article	Design of Adaptive Observer for Sensorless Vector Control of IM
72.	2000/11	Article	Sensorless Control of PM Motor with Damper Winding
73.	2000/08	Article	Improvement of Constant Trace Algorithm for Identification of Induction Machine Rotor Time Constant
74.	2000/08	Article	Practical Cnsideration of Sensorless Vector Controlled Induction Machines Based on Extended Kalman Filter
75.	2000/08	Article	Sensonless Vector Control of Induction Machines based on Adaptive Observer -Design by using Coefficient Diagram Method-
76.	2000/05	Article	Friction Compensation with Neural Network for Linear Motors
77.	2000/05	Article	Reduction of Thrust Force Pulsation of Linear Brushless DC Motor with Position Observer and Electromotive Force Observer
78.	2000/04	Article	Zero Frequency Operation for Sensorless Vector Controlled Induction Machines using Extended Kalman Filter The Institute of Electrical Engineers of JapanInternational Power Electronics Conference, Volume4,pp.5(2082-2086) (Collaboration)
79.	1999/10	Article	Sensorless Vector Controlled Induction Machine Drives with Fast Stator Voltage Offset Compensation IEEEIndustry Application Society Annual Meating pp.4 (Collaboration)
80.	1999/09	Article	Stable Identification of Rotor Time Constant for Induction Motor using Fixed Trace Algorithm Swiss Federal Institute of Technology LausanneEuropean Conference on Power Electronics and Applications pp.6 (Collaboration)
81.	1999/03	Article	Lower Speed Range Drive for Sensorless Vector Controlled Induction Machines with Stator Voltage Offset Compensation Method The Institute of Electrical Engineers of Japan (Collaboration)
82.	1999	Article	Lower Speed Range Drive for Sensorless Vector Controlled Induction Machines with stator voltage offset Compensation Method The Institute of Electrical Engineers of Japan pp.D・3
83.	1999	Article	Stable Identification of Rotor Time Constant for Induction Motor Using Fixed Trace Algorithm European Conference on Power Electronics and Applications
84.	1997/08	Article	Behavior of Sensorless Induction Motor Drives in Regenerating Mode Power Conversion Conference - Nagaoka 1997 pp.549-552 (Collaboration)
85.	1997/08	Article	Induction Motor Control for Electric Vehicle Application Using Low Resolusion Position Sensor and Sensorless Vector Control Technique Power Conversion Conference-Nagaoka 1997 pp.937-942 (Collaboration)
86.	1997	Article	Behavior of Sensorless Induction Moter Drives in Regenerating Mode 共 Power Conversion Conference-Nagaoka pp.549-552
87.	1997	Article	Induction Motor Control for Electric Vehicle Application Using Low Resolusion Position Sensor and Sensorless Vector Control Technique 共 Power Conversion Conference-Nagaoka1997 pp.937-942
88.	1997	Article	Potor Resistance Adaptation for Sensorless Vector Controlled Induction Machines Transactions, IEE of JAPAN pp.940
89.	1997	Article	Sensorless Vector Control of Induction Machines with Stator Voltage Offset Compensation European Conference on Power Electronics and Applications pp.4508-4511 (Collaboration)
90.	1996	Article	The Improvement of Performance at Low Speed by Offset Compensation of Stator Voltage in Sensorless Vector Controlled Induction Machines IEEE IAS(Industry Applications Society)Annual Meeting pp.257-261
91.	1995	Article	Influence of Magnetic Saturation on Rotor Resistance Adaption in Field-Oriented Induction Motor Drives without Speed Sensors International Conference on Power Electronics (IPEC), /,1040- 1043(1995) pp.1040-1043
92.	1995	Article	The Improvement of Performance at Low Speed by Offset Compensation of Stator Voltage in Sensorless Vector Controlled Induction Machines Transactions, IEEE of Japan pp.952-953
93.	1994	Article	Speed Sensorless Field Oriented Control of Induction Motor with Rotor Resistance Adaptation IEEE Trans.on Industry Applications IA-30.5,pp.1219-1224 (Collaboration)
94.	1994	Article	Speed Sensorless Field-Oriented Control of Induction Motor with Rotor Resistance Adaptation IEEE Transactions on Industry Applications 30(5),pp.1219-1224
95.	1993	Article	DSP-based Speed Adaptive Flux Observer of Induction Motor IEEE Trans.on Industry Applications IA-29.2,pp.344-348 (Collaboration)
96.	1993	Article	Speed Sensorless Field Oriented Control of Induction Motor with Rotor Resistance Adaption IEEE IAS(Industry Applications Society)Annual Meeting
97.	1992	Article	Compensation for Core Loss of Adaptive Flux Observer-Based Field- Oriented Induction Motor Drives International Conference on Industrial Electronics, Control, Instrumentation, and Automation pp.67-71
98.	1992	Article	Compensation for Core Loss of Adaptive Flux Observer-Based Field-Oriented Induction Motor Drives International Conference on Industrial Electronics, Control, Instrumentation, and Automation pp.67-71
99.	1992	Article	Robust Field Oriented Induction Motor Drives based on Disturbance Torque Estimation without Rotational Transducers IEEE Industry Applications Society Annual Meeting pp.558-562
100.	1992	Article	Simultaneous Estimation of Speed and Rotor Resistance of Field Oriented Induction Motor without Rotational Transducers Transactions, IEEE of Japan pp.901-902
101.	1991	Article	Adaptive Flux Observer of Induction Motor and its Stability Transactions, IEEE of Japan pp.188-194 (Collaboration)
102.	1991	Article	Direct Field Oriented Control of Induction Motor without Speed Sensors using Adaptive Flux Observer Transactions, IEEE of Japan pp.954-960 (Collaboration)
103.	1991	Article	Disturbance Torque Compensation of Adaptive Flux Observer Based Field Oriented Induction Motor Drives without Speed Sensors Transactions, IEEE of Japan, 111-D/10,899-900(1991) pp.899-900
104.	1986	Article	Analysis of New Current Source GTO Inverter Fed Induction Motor Drive IEEEIEEE Trans.on Power Electronics PE-1.4,pp.210-214 (Collaboration)
Display 5 items
Display all(104)

■ Academic Qualifications

1.	～1984	〔Master Course〕, Graduate School, Division of Engineering, Meiji University,
2.	～1982	Faculty of Engineering, Meiji University,

■ Academic Associations Membership

IEEE

■ Research Topics, Consignment Studies & KAKENHI Researches

1.		"Study on Motor Drives (Sensorless Drive,Induction Machines,Linear Motors)" (Key Word : ",,")
2.		Study on Motor Drives (Key Word : Sensorless Drive,Induction Machines,Linear Motors)

■ Current Specialized Field

Power engineering, Power engineering, Power engineering, Control and system engineering